This article applies to Videon devices running the Supervisor Web UI introduced in V13.0.0. If your device shows the earlier Web UI without the Supervisor sidebar, use Setting up password protection (earlier Web UI).
Password protection helps control access to your Videon device's Web UI. When enabled, users are prompted to sign in before they can access any part of the interface. This protection applies across the entire Web UI, including the Encoder application.
Looking for the previous password protection settings?
In earlier software versions, password protection was configured under Device Settings > Security within the Encoder UI. In Supervisor-based releases, password protection is now managed from Device Settings > Advanced > Open Supervisor Web UI. Then Platform > Settings > Supervisor.
Table of Contents:
- Turn on password protection
- Sign in for the first time
- Change a password later
- Review and manage accounts
- Turn off password protection
- Secure Mode
- Protect credentials with HTTPS
- If the password is lost
-
Turn password protection on or off remotely
Turn on password protection
- Open Supervisor in a supported browser using the local web UI at the device's IP address and navigate to Device Settings > Advanced > Open Supervisor Web UI.
- In the sidebar, expand Platform and select Settings.
- Select the Supervisor tab and find the Access section.
- Turn on Require authentication.
- Select Save.
After saving the change, Supervisor immediately enables password protection and adds a Users tab to the settings page. The next time the Web UI is accessed, users will be prompted to sign in before viewing the interface.
Be sure to store the administrator username and password in a secure location along with the device information. If all administrator credentials are lost and no authorized user can access the device, a factory reset may be required to restore access. See What if I forget my security password to my encoder?
Sign in for the first time
Password protection includes a built-in administrator account with the admin role. During the first sign-in, you will be prompted to replace the temporary password before continuing.
- Open the device address in a browser. The sign-in page appears.
- Enter the administrator credentials and select Sign in.
- Supervisor opens the change-password page, which states that a new password must be set before continuing because the default password is temporary. Enter the new password twice and select Update password.
Passwords must be at least eight characters long. Supervisor enforces no other composition rules. For improved security, consider using a unique password that follows your organization's password guidelines.
Change a password later
Select the account name in the Supervisor header and choose Change password. Enter the current password, enter the new password in New password (min 8 characters) and Confirm new password, then select Update password. Supervisor re-establishes the session with the new password, so no further sign-in is needed.
The same menu contains Logout, which ends the session and returns to the sign-in page.
Review and manage accounts
The Users tab appears under Platform > Settings whenever password protection is on. The tab displays available user accounts along with their assigned roles and current status. Supervisor supports the admin, operator, and viewer roles.
Creating and editing accounts requires the user-management entitlement. On an entitled device, the tab adds:
- Add user to create an account with a username, a password of at least eight characters, a display name, an email address, and one or more roles.
- Reset password to set a new password, with the option to Require change on next login.
- Delete user to remove an account permanently.
- A details pane showing the profile, account status, account source, roles, and active sessions with the originating address, start time, expiry, and browser for each session.
Turn off password protection
- Go to Platform > Settings > Supervisor.
- Turn off Require authentication.
- Select Save.
Once password protection is disabled, anyone with network access to the device can open the Web UI without signing in. For this reason, Videon recommends leaving password protection enabled whenever devices are deployed on shared or publicly accessible networks.
Secure Mode
Secure Mode, at the top of the same Access section, turns password protection on as part of a broader security posture and greys out the Require authentication toggle while it is active. Enabling it asks for confirmation and warns that Secure Mode forces HTTPS, standard web ports, and authentication, moves applications off host networking, and recreates containers. At least one user account is required.
Enabling Secure Mode recreates device containers as part of the security update process. Depending on the applications installed, additional container updates may be required afterward. Videon recommends enabling Secure Mode during a planned maintenance window and validating operation before returning the device to production use.
When Secure Mode is on, a videon-daemon exclusion option keeps videon-daemon on host networking so that RTSP, SRT, and RTMP streaming continues to work.
Protect credentials with HTTPS
Password protection controls access to the Web UI, but it does not by itself encrypt traffic between your browser and the device. To help protect login credentials and other Web UI traffic, Videon recommends enabling HTTPS whenever possible. The Web access section of the same tab configures HTTPS, which keeps credentials from crossing the network in plain text. The HTTPS list offers Off, Self-signed certificate, Upload certificate, and Automatic certificate (Let's Encrypt). Redirect visitors to HTTPS sends browser traffic to the secure address while local services on the device continue to use HTTP.
Changing the HTTP port, enabling standard web ports, or turning on HTTPS moves the Web UI to a different address. Note the new address before saving.
If the password is lost
If a password has been forgotten, it cannot be recovered from the sign-in page. On a device with the user-management entitlement, another account with the admin role can reset the password from the Users tab. If no administrator account can be used to reset the password, restoring access may require a factory reset. A factory reset returns the device to its default configuration, so be sure to review the reset documentation before proceeding.
See What if I forget my security password to my encoder? and LiveEdge Node/EdgeCaster Factory Reset.
Turn password protection on or off remotely
Password protection can also be managed from LiveEdge Cloud Control without opening the local Web UI. See LiveEdge Cloud Control: Setting up password protection.